What is Real User Measurements (RUM)?
Similar to website analytics products, RUM sends tracking beacons from your users' browsers to Neustar’s servers, and allows you to monitor performance of your site from your users' perspective.
When should I use Real User Measurements vs. Synthetic Monitoring?
- Real User and Synthetic monitoring serve different purposes and complement each other. Synthetic monitoring is great for detecting if your site is down, or establishing a baseline performance level, or investigating issues whether at the page element level or at the network level. Real user monitoring helps you get knowledge of your users' experience with your site. Real User Monitoring addresses several questions, including:
- What is my end user experience like? Do most end users have an acceptable experience or a frustrating one?
- I want to know my website performance with browsers my users are using.
- I want to know my website performance on the pages my users are going to. Synthetic monitoring cannot cover all paths of my website.
- I want to know my website performance from the locations my users are coming from. Synthetic monitoring does not have agents everywhere.
- I want to know my website performance from ISPs my users are connected to. Synthetic monitoring checks from data centers on fast Internet nodes do not give a realistic picture of my website performance as experienced by my users.
How do I get set up?
The latency is minimal, and the impact happens after the page load, causing no effect to users.
What browsers support the navigation timing method?
- Chrome 6+
- Firefox 7+
- Internet Explorer 9+
- Android Browser 4.0+
How do I find out if the tag is properly installed on my website?
- Once the tag is installed, go to the Live Feed tab of the Real User console in your Web Performance Management account. Then open a new browser tab and point your browser to your website. Once that page is loaded, you should see the measurement appear on the Live Feed map. Data should appear within a few seconds. If not, make sure that the tag is properly installed on your website using "View Page Source" from your browser. Remember that the RUM code snippet should be copied entirely and inserted just before the closing tag. Also, make sure when you test that your browser supports navigation timing api (see previous question). To investigate further, you can open your browser's Developer Tools and expand the network panel. In there, you should see 2 things related to RUM when you load your website's page: the beacon script "neustar.beacon.js" downloaded by your page, and the call to our servers at https://rum-collector.wpm.neustar.biz/beacon. This last call should return a HTTP status code 204 "No Content".
- If you still have an issue properly installing the tag, contact us at firstname.lastname@example.org.
What data is being collected?
What does the page load time over time graph show? How is the data aggregated?
The data we collect is aggregated every minute. At this point we aggregate only the page load time and the time to first byte. We calculate different metrics that we display for every minute and every hour in our main load time over time graph: average, min/max, Apdex score, load time distribution. All those are based on the page load time. In addition, we display the time to first byte average.
Why are the Real User Page Load times different than synthetic Page Load times?
- There are a number of factors that could explain that difference.
- First is the agent's location. Synthetic monitoring agents tend to be on high throughput networks whereas real users mostly use slower connections (DSL, cable). Also, the geographical distribution of those agents could impact the results.
- Second, the browsers used vary widely in a real user world whereas they are consistent in case of synthetic monitoring.
Why is my hits #s so low?
Since we are collecting only measurements done on browsers supporting the Navigation Timing API, there are a number of samples that are not saved on our servers. Our goal is to collect accurate measurements as opposed to all measurements. Also, we discard requests coming from our own synthetic monitoring agents.
Why do I see gaps in the page hits and Apdex graphs that do not show in the page load time graph?
The page load time graph is designed to show trends in page load time over time. For periods with no page hits, and therefore no page load time data, an interpolated line is shown spanning the time period.
Why are there no graphs displayed in Internet Explorer?
Internet Explorer version 8 and earlier do not have native support for Scalable Vector Graphics (SVG), which is required for Real User graphing. You can enable graphing in Internet Explorer by clicking the 'Install Google Chrome Frame' button under the Graphs tab of the Real User console and following the installation instructions. Google Chrome Frame is a free plug-in that adds SVG support to Internet Explorer.
How long is my RUM data stored?
- The individual requests are stored for seven days.
- The minute-level aggregate data is stored for seven days.
- The day-level aggregate data is stored indefinitely for now.
Is there an API I can use to retrieve my RUM data?
Yes. Learn more about Neustar Web Performance Management APIs.
Can I get a daily report in my mailbox with my RUM data?
Yes. From the Monitoring Reports tab, you can create reports that contain your RUM data as a Time Series graph. Reports can be sent daily, weekly or monthly.